Review of the C-Tug Trolley

When I purchased my Big Game a year ago I also purchased a C-Tug trolley at the same time. I knew the yak wasn't a light model and I had no intention of putting my back out, plus the majority of my launch sites see me parking the car far enough away to justify a trolley.

There are a few models to choose from out there, either the type that mount through the scupper holes or the 'cradle type' mount. The 'scupper hole' type trolley seems to produce quite some negative feedback with regards to cracking the scupper holes, that along was enough to put me off.

The C-Tug seemed was well spoken off both here in the UK and abroad so I parted with my £70 and duly took delivery of one.

C-Tug

Initial impressions were good, sturdy and simple with 2 straps allowing the yak to be secured to the trolley. Where to position the trolley?, I'm not too convinced on this at all. Positioning in the centre balances the yak nicely on the trolley meaning a light weight at the yak toggle when lifting it up to pull. However, perhaps due to the weight of the Big Game, the trolley pushes the base of the yak upwards by a good couple of inches where is sits against the trolley pads. I don't like this too much at all...

Mounting it further back around the seat scupper hole area, the base of the kayak is much stiffer due to the presence of the scupper holes and it sits far better as a result. However, when picking the front toggle up ready for moving the yak there is quite some weight on the toggle, not so pleasant.

Trolley in action

The strap assembly is flimsy with the locking mechanism manufactured from plastic, it didn't take too long to snap, though I've managed to modify it back to a working condition. A stainless mechanism would far better. The strap also has a tendency to slip causing the trolley to be dragged rearwards and ultimately tip over whilst going over soft terrain.

There is a steady leg to position the trolley prior to lowering the yak onto it, a great idea, though this will fall out at an early opportunity and is highly likely to be lost. Top tip, glue it in when you purchase it and then forget about it.

Leg - glued in

The wheels can be removed in seconds, as can the pad pieces which enables the C-Tug to be quickly dismantled and stored in the forward hatch of the yak. This is a great feature as there's no need to return a trolley to the car before launching, and it enables you to recover to a different location with ease. As said, the wheels remove from the stub axles', though the nature of this design allows sand, etc to penetrate this area which is a great recipe for wear and tear.

You'll hear a lot of squeaky C-Tugs, mostly down to this flaw in the design. The best you can do it to strip and thoroughly freshwater wash the trolley after each trip.

Early axle wear

The tyres are quite small and narrow, this is fine for surfaces such as concrete, hard wet sand, etc, though it causes a lot of problems over soft sand and shingle when the wheels simply dig in resulting in a lack of forward progress. As previously mentioned, in heavier conditions the yak can even 'roll' forward off the trolley causing the trolley to tip forward, very annoying!.

It’s quite unstable with my Big Game kayak on top, to the point where the trolley has tipped over on several occasions whilst navigating slightly uneven terrain, causing frustration and damage to fishing tackle. This is possibly partly down to the extra width of my Big Game compared to other kayaks, a wider track on the C-Tug would ultimately lead to improved stability.

So after a years use how do I rate it?.. to be honest it could be a lot better. I manage with it, though at times I could throw it in the bin. The fittings are poor quality considering the selling price and the design requires improvement. The 'pads' that support the yak need to be non-slip, the strap mechanism needs upgrading and it'd greatly benefit from wider tyres for floatation over soft sand and shingle.


LACING INSTRUCTIONS

There often seems to be confusion over setting up the straps on the C-Tug, below is the link to the official guide.

The Official Guide to Lacing the C-Tug


Please feel free to comment.

Crumbled Pouting Fillets

 

Serves 4

Ingredients

4 fillets of pouting, weighing about 200g each
100g plain flour
2 large eggs, lightly beaten
150g fairly fine fresh white breadcrumbs
250ml groundnut oil
Salt and freshly ground black pepper
For the tartare sauce
2 generous tablespoons mayonnaise (preferably homemade)
1–2 hard-boiled eggs, finely chopped
1 tablespoon roughly chopped parsley
1 teaspoon chopped dill
2–3 gherkins, finely chopped
2 teaspoons capers, finely chopped
Juice of ½ lemon


Method:
How to cook crumbed pouting fillets with chunky tartare sauce.

1. Make the tartare sauce first by simply stirring everything together in a bowl.

2. Set aside.

3. Put the plaice fillets on a board and skin them, then give them a quick bone check with your fingertips.

4. Put the flour in a deep plate and season it with salt and pepper. Put the beaten eggs and the breadcrumbs in two separate deep dishes.

5. Lightly coat one fillet of fish in the flour, shaking off any excess. Dip the floured fish in the egg, making sure it’s well coated, then roll it in the breadcrumbs so it’s generously covered. Repeat with the remaining fillets.

6. Set a large, fairly deep, non-stick frying pan over a medium heat and add the oil – it should be about 1cm deep.

Also works with:
Pollack
Whiting
Plaice
Megrim
Witch
Flounder

7. When it’s hot, fry the breaded fillets, in batches if necessary, for 2–3 minutes on each side, until golden brown and crisp.

8. Serve with the tartare sauce, along with buttered peas or creamed spinach and sautéed potatoes, chips or mash.