Rigging the Hobie Outback for fishing (Part1)

I’ve had the Hobie Outback for a few months now, rigging has been steady, perhaps a little pedestrian. A times parts have been slow to arrive, a lot of time has been spent planning and there’s been fishing, Christmas, Easter and other holidays and weekends away in between.

I’ve rigged several kayaks before, mostly for other people. The Outback had to be capable of being fished in various guises, anchoring, fishing with live or deadbait, trolling, lure fishing and sailing. Obviously not all at once!, however, It needed to be rigged in such a way that would permit the role of the kayak to be changed quickly and with minimal fuss. Consideration was also given to safety and I decided early on that I’d be fitting a bilge pump. It’s something I’d always wanted to fit to my Big Game, though I never got around to doing it. With the Outback I had a plain canvas, and with several years of experience behind me, I wanted to get it right from day one.

The rigging is now effectively completed, sure, there’s a couple of minor changes that I’ll embody in time, though for all intents and purposes it’s finished and ready to tackle anything that I choose to throw at it.

Below are two photos, the first one shows the Outback as it was supplied, the one below that shows the rigging complete, but with the kayak fully stripped for storage/transport.

Hobie Outback (as supplied)

Hobie Outback (Fully rigged and stripped)

At a glance there’s not a lot of difference to be honest, though that kayak can now be rigged to sail and/or fish in a matter of minutes, day or night. Look closely and you’ll see various pieces of GearTrac, a couple of cleats and two rod holders (removable if required). Look a  little closer and you’ll notice electrical cables, the kayak is fully wired to permit the connection of a battery to power up a fish finder, GPS, a bilge pump plus a navigation light.

There’s a crossbar fixed behind the seat, this permits the fitment of Hobie Sidekicks (click the link for the full article) which are ideally suited to sailing or perhaps fishing in rough seas. There’s also an anchor trolley system fitted, a must for anchoring in tidal waters and anchoring duties in general. Also visible on the other side of the kayak, close to the nose is another trolley system. This is actually a half-trolley and was fitted to permit the use of a drogue whilst anchored.

With a few pointers you may notice that the rudder is larger than the standard item, having being upgraded to a ‘sailing rudder’. At the rear left of the kayak (behind a section of GearTrac) is a flush outlet for the bilge pump. So at a glance there’s not much change, however, there’s actually many hours of planning and rigging taken place to reach that point.

Rigging for ‘basic fishing duties’

Below there’s a few photos showing the rigging that I’d consider ideal for standard fishing duties, whether it be anchored up or drifting. This would perhaps permit some lure fishing, fishing with dead baits, perhaps a livebait if caught and used immediately.


The only additions have been my trusty dry box, a GoPro Hero 2 camera mounted up front on a PanFish Portrait. The PanFish is mounted to a piece of YakAttack’s GT90 GearTrac, another piece is mounted on the rear upper side of the dry box, the latter allowing the fitment of a VisiCarbon Pro flag/light and my camera monopod. The GoPro is remote controlled so it’s position up front is not a concern.

The GearTrac is strong and versatile, permitting the quick and easy fitment and removal of suitably equipped accessories as required. I also have four piece of GearTrac GT175 positioned around the kayak, more on that later.

There’s a anchor reel and anchor situated in the front hatch (in the Hobie hatch liner – not shown), though the dry box also features two anchor stowages, so there are various options for storing the anchor & reel. The kayak trolley is fitted upside down, located in the tank well scupper holes and secured using the forward straps on the dry box.


I fitted additional stainless steel pad eyes either side of the seat to permit the front securing straps of the dry box to be attached kayak. There are Hobie mounting points either side of the dry box though their positioning was unsuitable, however, they are perfect for securing the Hobie Livewell. As can be seen in the photos above, I’ve run two continuous lengths of bungee cord around the dry box to permit items to be easily stored, yet remaining readily available. I keep by  removable cutting board and paddle float secured in these positions.

The cutting board is a must for bait fishing and was simple enough to manufacture. I utilised a MightyMount from YakAttack and associated T-bolt, thus allowing it be fitted and removed from the front right GearTrac in seconds.

Ok, I’ll take a closer look at the permanent fit as well as the electrical items.

The rod holders are modified composite RAM tubes. I’ve fitted them on either side of the seat in the recesses that permits the storage of pliers, etc, whilst fishing. They weren't a straight forward fit and required spacers and a longer bolt for the handle to permit them to be correctly fitted. They’re ideally placed and provide an ‘armchair’ fishing position. Rod leashes are also attached in this location, keeping those expensive rods and reels leashed to the kayak at all times.

I found the centre 8” ‘Twist & Lock’ hatch not that user friendly to begin with. Like most hatches it opens up directly to the hull and does not permit the easy storage of tackle and other items. Hobie don’t produce a ‘hatch bag’ for the 8” hatch so after a some thought I produced my own hatch liner (click the link for the full article) for little money. The end result was a cavernous compartment that allows many items of tackle, a flask, food, etc, to be stored as required.

There was of course the requirement (luxury) of having an electronics fit. I did consider a fish finder/GPS combo unit, though once you combine the initial purchase price with a mapping card they suddenly become very expensive. I already owned a Garmin 60Csx GPS with Bluecharts, so I decided to stick with that and to add a new fish finder. After an awful lot of deliberation I settled on a Lowrance Elite 4x DSI. This is a small down imaging unit and from the various reviews that I’d read, it’s performance (and price) were quite impressive.

The GPS was already mounted to a RAM cradle and could be fitted to the GearTrac in seconds. The Lowrance is supplied with a rather bulky mount, though for some additional expenditure a dedicated RAM mount can be purchased (part No.RAM-B-101-LO11). This negates the requirement for the supplied Lowrance mount and permits the unit to be mounted directly to the GearTrac using a ScrewBall from YakAttack. Both the fish finder and the GPS are easily removed and stored for surf landings if required.


The transducer for the DSI units should ideally be placed outside the hull, as opposed to a ‘shoot through hull’ configuration and generally used with traditional sonars. This did prove somewhat difficult on the Outback as the only suitable mounting points were the rear scupper holes. I didn’t want to lose the facility of using the Hobie kayak trolley so an alternative mounting point was required. I’m not a fan of mounting a transducer on an ‘arm’, hanging it over the side of the kayak, though after quite some though I worked out that by removing the thread from a seat scupper that the transducer would pass through. The transducer mount needed quite some modification, though the end result was neat, tidy and very functional.


I’ll cover the fish finder installation in a little more detail at a later date. I also took the opportunity to fit a an electric bilge pump (click the link for the full article) to enable water to be quickly removed from the hull should I ever experience a leak whilst I’m afloat. Sure, it’s unlikely, but if it does happen I’ll certainly be happy that I took the time to fit the system.


The last electrical item that I fitted was a homemade navigation light. It’s nothing special, an off the shelf light unit, aluminium pole, foam grip and a waterproof plug. I modified the base, fitting a T-Bolt from YakAttack, thus allowing me to fit the light to a section of GearTrac. A mating waterproof socket was fitted to the hull and it was wired into the main electrical loom. The light is easily removed when afloat and can be stored for surf landings if required.

The main wiring loom was made in one piece and fully sealed to prevent corrosion and the ingress of moisture.


An anchor trolley was also required so I chose to fit the genuine Hobie trolley system (click the link for the full article). This came supplied with some quality components and was fitted in well under an hour. I modified the suggested routing a little to meet my own requirements. It’s a full length trolley, running from the bow to the stern, permitting the positioning of the anchor anywhere along the trolley run.

As mentioned earlier, on the right hand side of the kayak I fitted a ‘half trolley’, running fully forward from the centre of the kayak. This was fitted purely to permit the use of a drogue whilst at anchor. If you’re subjected to a cross wind whilst at anchor the kayak will tend to swing across the tide. This can be quite annoying and doesn’t provide the best fishing position. With a drogue deployed just ahead of the kayak, with the trolley fully forward, the kayak will (with some tide running) swing back into the tide. I use this method a lot and it works extremely well.

This is my basic fishing setup and as I mentioned earlier I’ve already covered the rigging required for sailing the Outback. The Part 2 ‘Rigging the Outback’ will look at setting up the kayak for live baiting and trolling.


Anonymous said...

Do Hobie and Lowrance still have a partnership with regards to fish finders and kayak transducer mount options as I see other kayakers with Hobie connections appear to be fitting Lowrance fish finders?

Rob Appleby-Goudberg said...

Lowrance has clearly had input into the design of some recent Hobie kayaks as can be seen by the 'Lowrance Ready' transducer mounts. Lowrance has also sponsored the 'Hobie World Fishing Championships'.

However, if you're asking is Lowrance sponsoring/supplying Hobie Team members by default, the answer is a simple no. I purchased my unit from Pixmarine chandlers as I was impressed with the unit when I first got to use it last November. I have the Elite 4X DSI and its perfomance is excellent, it's compact and is superb value for money. That was my reason for making the purchase.

Anonymous said...

Thank you I am pleased to hear that the Hobie sponsorship and the Hobie partnership with Lowrance and the sponsorship of the Hobie World Championship by Lowrance and he fact that you have Lowrance advertised on your kayak plus any fish finder install covered by Hobie tech uses Lowrance fish finders had no influence whatsoever on your or other Hobie sponsored kayakers decision to fit a Lowrance fish finders as opposed to a Garmin or a Hummingbird. That this decision was purely on the merits of the Lowrance fish finder compared to other products and is a totally independent decision.

When we go to manufacturers web sites we read what they want us to read so its good to get independent views which may help other kayakers make a decision on which fish finder to buy.

Rob Appleby-Goudberg said...

The Daiwa and Lowrance stickers were left overs from the 1012 Hobie Worlds,they were both sponsors of the event. I just figured that they brightened up the kayak a little. That said the Daiwa ones are already falling off!.

I seriously liked the Humminbird DI units, the Lowrance DI units are depth limited to around 200'. This will at times prove a problem, though those type of deep water fishing trips are so rare that I decided I could live with it.

The other factor was the cost, the Lowrance was better value for money.

I originally purchased a new model Garmin 300C for the Outback, though I hated the electrical connectors, I could see them failing fairly quickly. Also the mount was bulky (as is the Lowrance mount), though RAM offered a 1" ball conversion for the Elite 4, negating the need for the bulky mount that it came supplied with.

The final factor was that I'd already used the Elite 4 DSI, whereas I had zero experience of the Humminbird DI unit. I'm learning how to use it at the moment, it'll take a good few trips to get is weighed off. I'll do a full review once I feel in a position to do so.

Rob Appleby-Goudberg said...

I see that you're based down in Newton Abbot, I can't say that I've fished down that way myself. Do you fish locally?, or head north to the Bristol Channel?

Unknown said...

Awesome write up! I will be making a few upgrades. Thanks